Introduction: GIPP-2000 laboratory small spray dryer is mainly used in universities, research institutes and food, biological, beverage, chemical, materials, pharmaceutical and other enterprise laboratories to develop and produce micro-particle powder, for all solutions such as emulsions and suspensions. Broad-spectrum applicability, suitable for the drying of heat-sensitive substances such as biological products, biological pesticides, enzyme preparations, etc., because the materials ejected are only subjected to high temperature when sprayed into mist-sized particles, so they are only heated instantaneously. These active materials are maintained to maintain their active ingredients intact after drying. Features: 1. GIPP-2000 laboratory small spray dryer adopts imported nozzle, high efficiency 2. The machine has 485 communication interface, which can be controlled remotely, especially suitable for laboratories or factories with relatively complicated working environment (optional) 3. Using color LCD large LCD touch screen operation, automatic control and manual control combined 4. Full-automatic control: After one-button start-up, after setting the spray process parameters, the temperature reaches the predetermined temperature and starts up automatically. The running animation is displayed on the touch screen, and the running process is clearly displayed; when the machine is shut down, just press the stop button and the machine automatically shuts down safely. 5. Manual control: If the process parameters need to be adjusted during the experiment, it is convenient to switch to the manual state. The color touch screen is dynamically displayed (animation) throughout the experiment. 6. Shutdown protection function: After the instrument is finished, the working state of the fan should be kept, so that the glass is partially cooled. The machine is set by intelligent program. When the inlet temperature is lower than 30 degrees, the fan is automatically turned off, no need to manually close the fan; protection The device does not burn the heating element due to misoperation (forcibly shutting off the fan) 7. Time setting function: The user can set the working time of the machine by himself, without manual guarding, and the working time ends the machine to stop working, which greatly saves the precious time for the customer to do the experiment. 8. The laboratory small spray dryer has a built-in oil-free air compressor. The air compressor is equipped with a stainless steel gas storage tank. The diameter of the powder spray is normally distributed, the fluidity is good, and the noise is very low, which meets the national laboratory noise standard. ; 9. The atomization structure of the two-fluid spray, the whole machine body is precision-made by high-quality stainless steel material, compact in design, no need for auxiliary equipment, convenient to use, and lasts for a long time. 10. The spray, drying and collection system is made of transparent high-quality borosilicate heat-resistant glass material, which makes the drying process in a non-polluting environment; and makes the whole spray drying experiment process transparent and intuitive, all the original glass parts are easy to remove and wash. ; 11. In order to meet the requirements of the user to adjust various parameters in the experimental range, the real-time control PID constant temperature control technology is adopted in the design of the drying temperature control, so that the temperature control in the full temperature zone is accurate, and the heating temperature control precision is ±1 °C. Technical Parameters: 1, spray dryer automatic control and manual control dual control mode, the entire experimental process color touch screen dynamic display (animation) air inlet temperature / outlet temperature / peristaltic pump speed / air volume / needle frequency 2, inlet air temperature control: 30 ° C ~ 300 ° C 3, the outlet temperature control: 30 ° C ~ 140 ° C 4. Evaporation water volume: 1500mL/H～2500ml/h 5, the maximum feed amount: peristaltic pump adjustable up to 2500ml / h 6, the minimum amount of feed: 30mL 7, the host stainless steel material, never rust corrosion, high quality borosilicate heat-resistant drying chamber, high-quality high borosilicate heat-resistant cyclone separator, high-quality high borosilicate heat-resistant sample collection bottle, high-quality borosilicate heat-resistant sample collection tube . 8. Real-time PID temperature control technology, real-time online display of inlet air temperature and outlet temperature, temperature control accuracy ±1 °C 9, drying time: 0.8 ~ 1.5S 10. The machine has the function of misoperation protection. When the order of the fan and heater switch is wrong, the machine automatically reminds you to prevent the novice from mishandling the machine. 11. The small spray dryer has the shutdown protection function: just press the stop button when shutting down, the machine will stop running immediately except the fan to ensure that the equipment will not burn out due to misoperation (forced off the fan). 12, nozzle diameter: 0.5mm / 0.7mm / 0.75mm / 1.0mm / 1.5mm / 2.0mm optional, and can be customized according to requirements 14. After drying, the finished dry powder has a relatively uniform particle size, and more than 95% of the dry powder is in the same particle size range. 15. For the adhesive material, there is a nozzle cleaner (through needle), which will automatically clear when the nozzle is blocked, and the frequency of the needle can be adjusted automatically. 16, intelligent control system, replacing the PLC control on the market, the stability is stronger, 17. Automatic fan stop function: After the instrument is finished, the working state of the fan should be kept, so that the glass is partially cooled. The machine is set by intelligent program. When the inlet temperature is lower than 30 degrees, the fan is automatically turned off, and there is no need to manually close the fan manually. 18, air compressor: 0.2KW maximum gas production 4.2m3 / h, compressed air working pressure: 2 ~ 3Bar 19, the whole machine power: 3.8KW/220V 20, fan: 0.6KW maximum air volume 5.6m3 / min maximum wind pressure 1020Pa 21, external dimensions: 1300mm (height) × 650mm (length) × 500mm (width)
Introduction: GIPP-2000 laboratory small spray dryer is mainly used in universities, research institutes and food, biological, beverage, chemical, materials, pharmaceutical and other enterprise laboratories to develop and produce micro-particle powder, for all solutions such as emulsions and suspensions. Broad-spectrum applicability, suitable for the drying of heat-sensitive substances such as biological products, biological pesticides, enzyme preparations, etc., because the materials ejected are only subjected to high temperature when sprayed into mist-sized particles, so they are only heated instantaneously. These active materials are maintained to maintain their active ingredients intact after drying.
